Thinkcar ThinkScan Max2 OBDii Code Reader All Cars Scanner Wit Resets And Programming Functions

New Thinkcar Thinkscan Max2 5.99 Inch Professional  Automotive Code Reader Tester Full System with Free 28 plus Reset Function +Free Upgrade More than 1000+ Cars + Bluetooth / Wifi connection ,Supported Auto VIN Scan /ECU Coding/A/F Reset/ Action Test OBD2 Scanner Thinkscan Max.
NOTE: Please Select those Vehicles (Cars software and Reset functions) That are relevant to you during system Update, 
Introduction
* Thinkscan Max2 as the Highest-level FULL OBD II Diagnostic Device For DIY users supported include Code Reading/Clearing data stream,Actuation Test ,Special Functions etc* Free Use Reset Service function 28 puls * Intelligent vehicle model identification via VIN* no need the cables contact with Car ,More Convenience* Free Upgrade Online for life time
Full 10 Mode OBDII/EOBD/JOBD Car Diagnostics
1.Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)
2.Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.
3.Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
4.I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
5.Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.
6.View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
7.O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
8.On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
9.Read Vehicle Information:Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
10.Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.
Thinkscan Max Supported 28 Kinds of Reset Service
1.Oil Reset :allows you to perform reset for a new calculation of Engine Oil Life system once changed the oil.2.EPB Reset : is important in the maintenance of electronic braking system's safety and efficiency.3.BMS Reset: allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement, and activate the rest state of the vehicle.4.DPF Reset: specially works for Particulate Filter system with DPF regeneration, DPF component replacement teach-in and DPF teach-in after replacing the engine control unit.5.SAS Reset: helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration.6.TPMS Reset :makes sense in displaying sensor IDs from the vehicle's ECU, inputting TPMS sensor replacement IDs and testing sensors.7.IMMO reset: it is mainly used to disable the lost vehicle keys and program a new replacement key fob.8.ABS Bleeding: ABS brake bleeding to get a firm brake pad after air exhaustion.9.Throttle reset: The throttle body is a tube containing a pivoting flat valve (butterfly) that is used to control the amount of air entering an engine. In an electronically fuuuil injected car, a throttle position sensor and air flow sensor communicate with the computer, which supplies the corresponding amount of fuuule needed at the injectors. It must need re-learning throttle sensor position after clearing or repair10.Injector Coding: Leaking injectors and some dead injectors can be missed even when an injector is disabled. Other problems with the ignition system and mechanical components also may not show an rpm loss when an injector is turned off.11.Gear LearningAfter the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced, or the  DTC 'tooth not learned' is present, tooth learning must be performed.12.Suspension MatchingAdjust the vehicle height sensor for level calibration.13.Sunroof Initialization:Set the sunroof lock off, close in rain, memory function of sliding 1 tilting sunroof, outside temperature threshold, etc.14.Battery Matching:By clearing the original breakdown information about the lack of battery power,rematch the battery.15.A/F ResetApplied to set or lean Air/Fuuil ratio parameters.16.Steering Angle Resethelps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration. Thinkscan Max Supported 28 Kinds of Reset Service
1.Oil Reset :allows you to perform reset for a new calculation of Engine Oil Life system once changed the oil.2.EPB Reset : is important in the maintenance of electronic braking system's safety and efficiency.3.BMS Reset: allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement, and activate the rest state of the vehicle.4.DPF Reset: specially works for Particulate Filter system with DPF regeneration, DPF component replacement teach-in and DPF teach-in after replacing the engine control unit.5.SAS Reset: helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration.6.TPMS Reset :makes sense in displaying sensor IDs from the vehicle's ECU, inputting TPMS sensor replacement IDs and testing sensors.7.IMMO reset: it is mainly used to disable the lost vehicle keys and program a new replacement key fob.8.ABS Bleeding: ABS brake bleeding to get a firm brake pad after air exhaustion.9.Throttle reset: The throttle body is a tube containing a pivoting flat valve (butterfly) that is used to control the amount of air entering an engine. In an electronically fuuli injected car, a throttle position sensor and air flow sensor communicate with the computer, which supplies the corresponding amount of fuuli needed at the injectors. It must need re-learning throttle sensor position after clearing or repair10.Injector Coding: Leaking injectors and some dead injectors can be missed even when an injector is disabled. Other problems with the ignition system and mechanical components also may not show an rpm loss when an injector is turned off.11.Gear LearningAfter the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced, or the  DTC 'tooth not learned' is present, tooth learning must be performed.12.Suspension MatchingAdjust the vehicle height sensor for level calibration.13.Sunroof Initialization:Set the sunroof lock off, close in rain, memory function of sliding 1 tilting sunroof, outside temperature threshold, etc.14.Battery Matching:By clearing the original breakdown information about the lack of battery power,rematch the battery.15.A/F ResetApplied to set or lean Air/Fuuli ratio parameters.16.Steering Angle Resethelps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration.